- Are you supposed to drill into studs?
- Are there wires on studs?
- What is code height for electrical switches?
- How do I know where the wires are in my wall?
- How high off the ground should electrical wires be?
- Can you run electrical wire behind studs?
- Can you run electrical wire horizontal?
- Can I wire outlets and lights on same circuit?
- Do electric wires run up or down?
- Do stud finders detect wires?
- How far behind drywall are wires?
- Why do stud finders not work?
- What happens if I drill into a wire?
- How many outlets can be on a breaker?
- Can I use my iPhone as a stud finder?
Are you supposed to drill into studs?
If you’re hanging shelves or mounting anything heavy to the wall, you’ll probably want to mount it directly to the wall studs.
However, you should be drilling pilot holes first before driving in any screws..
Are there wires on studs?
“Electrical wires often run vertically along studs,” says Matt Daigle, founder and CEO of sustainable home improvement site Rise. … Since studs are typically spaced 16 to 24 inches apart, you won’t have to search very long to find your first one. Be sure to invest in the right kind of stud finder, though.
What is code height for electrical switches?
48 inchesLight Switch Positioning: All switches positioned at 42″ to the centre of the electrical box from the finished floor. The light switch height standard of 48 inches came from over 100 years ago at the turn of the century when electricity was first being introduced into housing.
How do I know where the wires are in my wall?
Before drilling, find out exactly where the wiring is.Place the stud finder with wire tracing mode onto the wall. … Move the finder along the wall, front towards you and the flat side against the wall. … Move the stud finder over the electrical wires.More items…
How high off the ground should electrical wires be?
18 feetPower Lines Over Streets and Roadways With Commercial Traffic. For any driveways, alleys, roads, or streets likely to carry vehicles more than 8 feet in height, the guideline is for all power lines to be at least 18 feet above the ground measured at their lowest point.
Can you run electrical wire behind studs?
Yes, you can run the cable behind the studs. In these situations, you often see the electrician only drill a hole in every other stud and run behind the stud between. You can also afford to offset the drilled holes towards the back of the stud to get them even farther from possible damage from nails.
Can you run electrical wire horizontal?
Yes you can,the 17th regs says cables should be run verticaly or in safe zones you can also run horizontaly between two live points,in other words socket to socket.
Can I wire outlets and lights on same circuit?
Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes. The neutral will be white but some switches are wired up with a white wire that is not a neutral. … As a rule of thumb in counting devices on a circuit you count each outlet (light or receptacle) as 1.5 amps.
Do electric wires run up or down?
Electrical wires typically run either vertically, up and down the side of a stud or horizontally. The vertical wires are typically pretty easy to avoid: avoid drilling above a receptacle or light switch.
Do stud finders detect wires?
Using an electronic stud finder, you can detect live wires behind the walls or through the studs. An electronic stud finder is a tool that will let you find studs, beams, joists, or wires.
How far behind drywall are wires?
Electrical cables are usually behind drywall, either running horizontally through holes in the studs or stapled vertically up the sides of studs. Outlet cables tend to be about 12 inches high. Light switches are around 48 inches high, so expect to see electric cables around that area.
Why do stud finders not work?
1) Check Your Battery. If your stud finder worked previously, but no longer seems to work, about 9 times out of 10, the problem is a weak battery. You may swear that the battery is still good, but it’s not. … Compared to garage doors and many other devices, stud finders require a very strong battery.
What happens if I drill into a wire?
Damage to electrical wiring from drilling into walls is a surprisingly frequent phenomenon – especially when buildings are being renovated. Not only do the lights go out, but you usually blow a fuse as well. With a bit of luck, you might only have to repair the cable sheath.
How many outlets can be on a breaker?
I’m ask so many times how many outlets and or lights can I put on a 15 amp or 20 amp breaker. Well NEC code does not have it listed that way. By rule of thumb you would stick with 8 to 10 outlets and or lights per breaker.
Can I use my iPhone as a stud finder?
The iPhone beeps when its magnetometer, in the upper right of the phone, is near metal. Stud Find is an iPhone application that uses the device’s built-in magnetometer to find metal studs, screws, nails and anything metallic in a wall.