Will Home Depot Trim A Door?

How high should a door be off the floor?

What is the ideal clearance between the door bottom and the finished floor.

The ideal clearance, or height, of a door above finished flooring is 3/8 inch and certainly no more than 1/2 inch.

The height of interior doors above finished floors can also be an issue..

Can you trim a door with a router?

When trimming doors to length, the cutter must have enough length to cut the thickness of the door. This will in most cases necessitate the use of a long reach cutter with 1/2¨ shank cutter and a heavy duty router. … Measure the distance from the outside edge of the cutter to the straight edge of the base.

Can you trim the side of a door?

Don’t cut more than 3/4 inch from the side of any door. Any more than that and the doorknob won’t work properly or the side of the door will be too thin, causing it to warp or separate. Wear safety glasses when working with saws or wood.

How much should I cut off the bottom of a door for carpet?

Typically you only need to trim 1/2 inch from the bottom of the door. If that’s not enough, you can trim off up to 3/4 inch. Hollow-core doors, which are the most common for interior usage, are built around a frame on the outside perimeter. If you cut too much off the frame, the door will can separate.

Can you trim a pre finished door?

For an exact fit, most doors will require a small amount of trimming. While fire doors , bi-folding doors , and rebated door pairs cannot be trimmed, other internal doors can. … Ensure you fully treat any edges you trim, even if they are pre-finished doors, as trimming will expose the timber.

How do you cut the bottom of a wood door?

When you need to cut the bottom of a door, use a straightedge, a circular saw, and these tips for an accurate and clean jobStep 1: Mark the door for the cut. … Step 2: Draw the cutline. … Step 3: Score the cut to prevent tearout. … Step 4: Make a gauge block.More items…•

What saw to use to trim a door?

A circular saw makes a great door cutter. Make sure your saw blade is sharp and has a minimum of 18 teeth. Hold the circular saw against the edge of the door as if you’re ready to cut.

Can solid core doors be trimmed?

If one is cutting down a “solid core” door, clean out the core material as David described, then use the cutoff piece to reblock the door. You will need to clean off the skins, but the piece should fit back in well.

How much can you trim from a door?

Most internal doors manufacturers advise different trimming tolerances so as a standard and to be on the safe side we advise that you don’t trim more than 5mm per side. This is with the exception of LPD, which only allow 3mm on each side.

How much can you cut off the bottom of a solid core door?

The maximum amount allowable to trim off any standard 80 inch door is 39 1/2 inches off both the top and the bottom.

Can I cut a door to size?

Most manufactures have a piece of wood on the bottom of the door which allows the door to be trimmed to size. The size of this depends upon the manufacture. A good rule of thumb is there is a 1″ piece of wood in place. If you have to cut larger than that, you could ruin the door, but again there are tricks to that.

How much can you trim off a Prehung door?

Check the length of your prehung door jambs. They may be longer than you need. You may have to trim both sides to minimize the space under the door. In most cases, the door should clear the floor by 1/2 in.

Can you cut 2 inches off a door?

While it is possible to trim hollow core doors, it isn’t always advisable. Removing an inch or two to allow for a thicker carpet or misread tape measure is fine, but cut off too much and you may notice that the bottom of the door is no longer solid.

Can you cut down a solid wood door?

Exterior wooden doors can have a core of either chipboard or solid wood with veneer on both sides, or they can have solid multiple panels inside a solid wood frame. Either way, they have a perimeter that can be cut down on either side or on the ends.

How much can I trim off the side of a hollow core door?

Typically you only need to trim 1/2 inch from the bottom of the door. If that’s not enough, you can trim off up to 3/4 inch. Hollow-core doors, which are the most common for interior usage, are built around a frame on the outside perimeter. If you cut too much off the frame, the door will can separate.

How do you shave the bottom of a door without removing it?

To sand the bottom of a door without removing it, put the sandpaper on the floor, grit side up, and pull the door back and forth across it. Planing is usually the last resort, since it will mean touching up the planed area with a sealer or finish to match the door. A rasp-type plane will often do the best job.